RhinoPower Ltd

Yez · Yez

Hi I have a problem identifying the diode that has failed in the Suzuki ECU. The marking on the diode is 5-6L2, but I cannot find any documentation about this diode. Does anyone know what can I buy a replacement for this diode? Is it an ordinary rectifier diode or a zener diode?

Minuti_1 · Minuti_1

Hello I am new here. I am helping a mate fit a G13BB (Sierra) into a little Minuti ute. I was wondering if you could help me with some questions re the wiring of this.Firstly, I am unsure what model the ECU came from; it was supplied with the engine. Secondly, the Loom/Plugs we have are from a G16B Baleno; u...

valimar · valimar

Hi All, I would like to ask your indulgence because this is my first post in this Forum.I have been busy for quite a time with my problem that in a few words I can resume in error code 81. Suzuki Forums have been of great help, mostly from Forem, (that advise me to contact Rhinopower), because my problems ar...

92SuzukiGT · 92SuzukiGT

Hi. I was pointed in the direction of this site just today. I have a 92 Suzuki Swift GT and I removed the stock chip and soldered in a 18 pin socket to use a turbo chip coming out of Australia from Redlinegti.com. I had melted off a couple pads being a newbie on electronic soldering. I thought I had fixed...

renatof · renatof

Hi guys! I'm new here in the forum so first I'd like to thank you for the great job already done!

I've read everything I could throw the documentation and here in the forum however it was impossible to find the DLC port down in my panel. I saw in another post that my Suzuki's Samurai 97 ECU was compat...

TechSupport · TechSupport

I have most of the schematics for this ECU and the source code. Ignition and fuelling tables are known. -- Edited by Rhinoman on Sunday 19th of May 2013 09:37:03 PM

Blazeking · Blazeking

Hello i am looking for the ecm tables for the attached ecm. I believe it is out of a 1992-1993 suzuki sidekick manual trans but i am not sure as the engine was swapped into my samurai before i purchased it. I am also looking for what the calibration settings are for the sensors on this engine to go aftermark...

Moto · Moto

Hi! G13bb engine from all auto is great engine for fly... So i need to try. But i need help for you... First. ECU. Need some help for rewrite corect firmware. i see Bosch ECU hardware for this engine...Practly this setting increase power from 86 to 100 hp .Important things is NO stop engine when is alar...

jjayp · jjayp

Hi there, im trying (what seems like in vain) to get my wifes GV repaired its only done 60k miles so i'm not inclined to bin it yet and don't mind spending a few hundred to get it fixed (obviously the cheaper the better). the car was left for a few months without being driven, the battery went dead and in betw...

enock katende · enock katende

am looking for those parts to fix my 1993 sierra suzuki- its a manual car. any body with knowledge of where to find them kindly contact me on +256772212240 and whatsapp +256700120240. thanks enock katende kaenomu@yahoo.com

TechSupport · TechSupport

This is an OBD2 ECU for a 1996 Suzuki Sidekick or Geo Tracker. The processor is an H8/536 which is very similar to the H8/532 processor used in the OBD1 models but with a few extra tricks thrown in. Its an OTP (one time programmable) device and requires a daughterboard to allow code modifications and rem...

Malodin · Malodin

Hi all, Ive been rebuilding suzuki ecms off and on since '05. I have about 10 samurai ecms that all have coil power but not injector action. I have 1 identical ecm that functions. Ecm# 80c30Board#e331a973a I have swapped the whole injector driver heatsink w/the 4 drivers from one of the bad bo...

Orchid70 · Orchid70

Hi I have not access to the car yet - Ive been told of this problem after changing the engine and now the car wont start and no engine ligt is present or milage counter - so - first plase to look is that the ECU is grounded properly. Before runnig to the car Id like to know a bit more about it =) Also - Id like to f...

TechSupport · TechSupport

This is an ECU for a carburetor equipped Super Carry with the 1ltr four cylinder engine. The controller used feedback from a lambda sensor and a mixture control solenoid on the carb to tune the air fuel ratio: The ECU is Aisin branded but is obviously made by Fujitsu Ten and uses a Ten branded microcont...

toyz · toyz

This ecu is from my 91 tracker. The 5vref board (E528A) seems to have died. Does anybody have a pinout for it or has anybody replaced it with a standard 5v ref IC. I saw a reference to some ECU schematics but the link does not work. Is there a new link.

Andrew · Andrew

Hi. I'm intending on transplanting an M16A engine into a classic car using a Jimny RWD gearbox. If I went for a Swift Sport engine, would I be able to use the ECU from the swift too? I think it would run better this way, rather than using an aftermarket ECU and having to map it. I've heard stories that some mo...

kabani · kabani

I have 2003 Jimny JLX. I have been trying to communicate with the ECU. There is continuity between DLC and ECU pins. But something caught my attention. There is no voltage in the k-line pin 7. I have read in someplaces that there should be some voltage and that aftermarket radios might be cause (actuall...

TechSupport · TechSupport

This is a fairly unusual ECU, a very early Vitara ECU which is a fuel and emissions systems controller only The Micro is a Mitsubishi branded 63B01 which is an evolution of the 6801 processor. E816 is the firmware version. This ECU could be modified with a daughterboard to enable it to be retuned but fo...

rab · rab

Does 1995 tracker ECU have a middle layer of tracesSpecifically a 33920-70EA. I suspect there is a middle layer of copper traces in these boards because I cant trace where the main relay pin A10 goes to any switching transistor.

TechSupport · TechSupport

Jimny 81A11 Diagnostic ID 1903 Diagnostic address known so far: Function Addr IAT 9 CTS 8 BATT 22 IAD n/c COAdj n/c TPS Angle 10 TpS Volts 11 Ground???? Trim1 19 Trim2 20 Trim3 21 2 trims are STFT and LTFT, 1 trim is ISC duty This ECU can be reprogrammed using the serial data link....

coma · coma

hi to all, i want to read this ecu because i swap engine 1.6 on my car. i want to adjiust fuel map for new engine can you help me? thanks Mauro from italy comatuning@gmail.com

SM7WDG · SM7WDG

I got a Suzuki X-90 for my kids (15-16 years old) . Here in sweden it is possible to rebuild a car to a "tractor". We call it "A-Traktor" There need to be done some things to make it legal for a kid to drive it. One of the things is to Make a speed limit to 30 Km/h. (10% margin is ok so 33 ) One thing we use to do is bu...

Matzam · Matzam

Good day all. I has the engine jimny jb23w 660 k6a turbo with half of the wiring was cut off. Can help me to find wiring diagram or ecu pinout. Ecu code 33920-81AG1

PhilJ · PhilJ

Hello I am using a Suzuki Swift K14B motor for a project building an ultralight. The ECU number is 33910-71LA0. The motor is 2012. Any idea how I can find out if the unrequired functions can be switched off or disabled? My main concern is related to the imobiliser and air conditioning and if they can be...

TechSupport · TechSupport

This is a JDM ECU, it has the same (MG2130) software as the 57B30 but emission controls are disabled.

Aceman · Aceman

I have scraped a geo metro 1995 with the intention of using the engine and FI system in a yamaha side by side atv. I have removed the eprom from the board, socketed the board and read the chip 112043-0241. Need an adx and xdf for this unit. Not sure how to attach my bin ? Thanks

rewalex · rewalex

hello dear colleges i start yhe reparation of my ECU 33920-56B80 i loose a lot of electrolite from my cap :( I change: Q101 2SB1020 Q102 2SD1415 C105 68UF@10V C103 47UF@63V C101 22UF@50V C111 100UF@63V R2(223) ERJ-8GEYJ223V - RES 22K OHM 1/4W 5% 1206 SMD parametres of R752 parametres of C1 and C48 I c...

alto_auto · alto_auto

Hi Rhinoman, I have found the ECU and the number is 33920-70F60. I also have found the .csv files. But i dont understand how to change these files (address mapping) to make it work with my ECU. Best regards, Alto_Auto PS In a previous post i mentioned a "floating point error" but this i hav...

Phan · Phan

Dear Sirs, Please give me advice. My car is Suzuki Carry Truck without Diagnostic connector I could not turn off MIL even though that no DTC happen. Car running well, no problem but MIL still ON. Replace new ECU, MIL turn off normally. I do not know how to erase suspend DTC turn off the MIL. or check DTC o...

Bumingdeath · Bumingdeath

Hello, i would need pinouts for this specific Ecm 33920-65G4 for my suzuki SJ410 engine swap, somehow i lost the largest obd1 A1 26pin connector but i managed to haul one from the junkyard and. Now i cant find any pinouts or repair manuals where to find electrical information for my proplem. Please h...

Topic		Started By	Replies	Views	Last Post
	ECU Suzuki identyfying the diode (Preview) Hi I have a problem identifying the diode that has failed in the Suzuki ECU. The marking on the diode is 5-6L2, but I cannot find any documentation about this diode. Does anyone know what can I buy a replacement for this diode? Is it an ordinary rectifier diode or a zener diode?	Yez	1	197	October 27th by Zukistedt
	Sierra 1.3 ECM/Wiring into Minuti Ute (Preview) Hello I am new here. I am helping a mate fit a G13BB (Sierra) into a little Minuti ute. I was wondering if you could help me with some questions re the wiring of this.Firstly, I am unsure what model the ECU came from; it was supplied with the engine. Secondly, the Loom/Plugs we have are from a G16B Baleno; u...	Minuti_1	1	185	Jun 16, 2020 by TechSupport
	ECU or Immobilizer that´sHi the question (Preview) Hi All, I would like to ask your indulgence because this is my first post in this Forum.I have been busy for quite a time with my problem that in a few words I can resume in error code 81. Suzuki Forums have been of great help, mostly from Forem, (that advise me to contact Rhinopower), because my problems ar...	valimar	11	244	May 27, 2020 by valimar
	Help Repairing 92 Suzuki Swift GT ECU (Preview) Hi. I was pointed in the direction of this site just today. I have a 92 Suzuki Swift GT and I removed the stock chip and soldered in a 18 pin socket to use a turbo chip coming out of Australia from Redlinegti.com. I had melted off a couple pads being a newbie on electronic soldering. I thought I had fixed...	92SuzukiGT	12	237	May 19, 2020 by 92SuzukiGT
	ECU 33920-81CF0 (Preview) Hi guys! I'm new here in the forum so first I'd like to thank you for the great job already done! I've read everything I could throw the documentation and here in the forum however it was impossible to find the DLC port down in my panel. I saw in another post that my Suzuki's Samurai 97 ECU was compat...	renatof	4	193	May 14, 2020 by renatof
	33920-70E10 - Vitara 1.6 8V TBI 1999 (Preview) I have most of the schematics for this ECU and the source code. Ignition and fuelling tables are known. -- Edited by Rhinoman on Sunday 19th of May 2013 09:37:03 PM	TechSupport	2	8396	Mar 27, 2020 by TechSupport
	33920-58B30 ecm stock ignition / fuel table dump? 1992-1993 sidekick 1.6 16v? (Preview) Hello i am looking for the ecm tables for the attached ecm. I believe it is out of a 1992-1993 suzuki sidekick manual trans but i am not sure as the engine was swapped into my samurai before i purchased it. I am also looking for what the calibration settings are for the sensors on this engine to go aftermark...	Blazeking	5	299	Mar 23, 2020 by TechSupport
	G13bb ECU with "aviation" settings (firmware) (Preview) Hi! G13bb engine from all auto is great engine for fly... So i need to try. But i need help for you... First. ECU. Need some help for rewrite corect firmware. i see Bosch ECU hardware for this engine...Practly this setting increase power from 86 to 100 hp .Important things is NO stop engine when is alar...	Moto	1	609	Sep 4, 2019 by TechSupport
	2004 Suzuki Grand Vitara auto 16V 1.6 petrol (Preview) Hi there, im trying (what seems like in vain) to get my wifes GV repaired its only done 60k miles so i'm not inclined to bin it yet and don't mind spending a few hundred to get it fixed (obviously the cheaper the better). the car was left for a few months without being driven, the battery went dead and in betw...	jjayp	4	531	Apr 29, 2019 by jjayp
	ecu 33920-81c10(e2t42871t) dom -mt and distributor with 3wire running from e picker (Preview) am looking for those parts to fix my 1993 sierra suzuki- its a manual car. any body with knowledge of where to find them kindly contact me on +256772212240 and whatsapp +256700120240. thanks enock katende kaenomu@yahoo.com	enock katende	4	687	Apr 22, 2019 by TechSupport
	33920-71EC1 1996 Sidekick/Tracker 1.6 16V US AT (Preview) This is an OBD2 ECU for a 1996 Suzuki Sidekick or Geo Tracker. The processor is an H8/536 which is very similar to the H8/532 processor used in the OBD1 models but with a few extra tricks thrown in. Its an OTP (one time programmable) device and requires a daughterboard to allow code modifications and rem...	TechSupport	9	2892	Jan 3, 2019 by Troubled-1
	1990-95 samurai(jimny) 80c30 ecm rebuild issues (Preview) Hi all, Ive been rebuilding suzuki ecms off and on since '05. I have about 10 samurai ecms that all have coil power but not injector action. I have 1 identical ecm that functions. Ecm# 80c30Board#e331a973a I have swapped the whole injector driver heatsink w/the 4 drivers from one of the bad bo...	Malodin	1	706	Jan 2, 2019 by Troubled-1
	G13BB Sweden sold Jimny 1999 - where is ECU ground point? (Preview) Hi I have not access to the car yet - Ive been told of this problem after changing the engine and now the car wont start and no engine ligt is present or milage counter - so - first plase to look is that the ECU is grounded properly. Before runnig to the car Id like to know a bit more about it =) Also - Id like to f...	Orchid70	0	669	Nov 9, 2018 by Orchid70
	33920-85750 1996 Suzuki Carry 1.0 (Preview) This is an ECU for a carburetor equipped Super Carry with the 1ltr four cylinder engine. The controller used feedback from a lambda sensor and a mixture control solenoid on the carb to tune the air fuel ratio: The ECU is Aisin branded but is obviously made by Fujitsu Ten and uses a Ten branded microcont...	TechSupport	10	2863	Oct 24, 2018 by Solac03
	33920-56b30 (Preview) This ecu is from my 91 tracker. The 5vref board (E528A) seems to have died. Does anybody have a pinout for it or has anybody replaced it with a standard 5v ref IC. I saw a reference to some ECU schematics but the link does not work. Is there a new link.	toyz	0	616	Oct 16, 2018 by toyz
	M16a engine transplant (Preview) Hi. I'm intending on transplanting an M16A engine into a classic car using a Jimny RWD gearbox. If I went for a Swift Sport engine, would I be able to use the ECU from the swift too? I think it would run better this way, rather than using an aftermarket ECU and having to map it. I've heard stories that some mo...	Andrew	0	576	Oct 5, 2018 by Andrew
	ECU k-line pin7 no voltage, Flashing checkengine code 17??? (Preview) I have 2003 Jimny JLX. I have been trying to communicate with the ECU. There is continuity between DLC and ECU pins. But something caught my attention. There is no voltage in the k-line pin 7. I have read in someplaces that there should be some voltage and that aftermarket radios might be cause (actuall...	kabani	8	706	Sep 25, 2018 by TechSupport
	33920-60A70 Suzuki Vitara1.6L 8V 1988 to 1990 (Preview) This is a fairly unusual ECU, a very early Vitara ECU which is a fuel and emissions systems controller only The Micro is a Mitsubishi branded 63B01 which is an evolution of the 6801 processor. E816 is the firmware version. This ECU could be modified with a daughterboard to enable it to be retuned but fo...	TechSupport	20	9039	Sep 13, 2018 by TechSupport
	Does 1995 Tracker/Sidekick ECU have a middle layer of traces (Preview) Does 1995 tracker ECU have a middle layer of tracesSpecifically a 33920-70EA. I suspect there is a middle layer of copper traces in these boards because I cant trace where the main relay pin A10 goes to any switching transistor.	rab	1	681	Jun 6, 2018 by TechSupport
	33920-81A11 Jimny 1999 G13BB (Preview) Jimny 81A11 Diagnostic ID 1903 Diagnostic address known so far: Function Addr IAT 9 CTS 8 BATT 22 IAD n/c COAdj n/c TPS Angle 10 TpS Volts 11 Ground???? Trim1 19 Trim2 20 Trim3 21 2 trims are STFT and LTFT, 1 trim is ISC duty This ECU can be reprogrammed using the serial data link....	TechSupport	5	3240	Mar 13, 2018 by coma
	suzuki jimny 33920-81A2 read? (Preview) hi to all, i want to read this ecu because i swap engine 1.6 on my car. i want to adjiust fuel map for new engine can you help me? thanks Mauro from italy comatuning@gmail.com	coma	0	742	Mar 13, 2018 by coma
	Speed limit Suzuku X-90 1996 (Preview) I got a Suzuki X-90 for my kids (15-16 years old) . Here in sweden it is possible to rebuild a car to a "tractor". We call it "A-Traktor" There need to be done some things to make it legal for a kid to drive it. One of the things is to Make a speed limit to 30 Km/h. (10% margin is ok so 33 ) One thing we use to do is bu...	SM7WDG	0	829	Nov 12, 2017 by SM7WDG
	Ecu 33920-81AG1 (Preview) Good day all. I has the engine jimny jb23w 660 k6a turbo with half of the wiring was cut off. Can help me to find wiring diagram or ecu pinout. Ecu code 33920-81AG1	Matzam	0	945	Oct 9, 2017 by Matzam
	33910-71LA0 - Suzuki Swift K14B (Preview) Hello I am using a Suzuki Swift K14B motor for a project building an ultralight. The ECU number is 33910-71LA0. The motor is 2012. Any idea how I can find out if the unrequired functions can be switched off or disabled? My main concern is related to the imobiliser and air conditioning and if they can be...	PhilJ	2	1283	Aug 16, 2017 by PhilJ
	33920-57B10 - Vitara 1.6 16V 1992 (Preview) This is a JDM ECU, it has the same (MG2130) software as the 57B30 but emission controls are disabled.	TechSupport	1	2479	May 18, 2017 by keshwa
	A5 1.3- FED 33920-51g7 (Preview) I have scraped a geo metro 1995 with the intention of using the engine and FI system in a yamaha side by side atv. I have removed the eprom from the board, socketed the board and read the chip 112043-0241. Need an adx and xdf for this unit. Not sure how to attach my bin ? Thanks	Aceman	0	966	May 8, 2017 by Aceman
	ECU 33920-56B80 reparatioin (Preview) hello dear colleges i start yhe reparation of my ECU 33920-56B80 i loose a lot of electrolite from my cap :( I change: Q101 2SB1020 Q102 2SD1415 C105 68UF@10V C103 47UF@63V C101 22UF@50V C111 100UF@63V R2(223) ERJ-8GEYJ223V - RES 22K OHM 1/4W 5% 1206 SMD parametres of R752 parametres of C1 and C48 I c...	rewalex	0	1084	Mar 5, 2017 by rewalex
	33920-70F60 Suzuki Alto ECU (Preview) Hi Rhinoman, I have found the ECU and the number is 33920-70F60. I also have found the .csv files. But i dont understand how to change these files (address mapping) to make it work with my ECU. Best regards, Alto_Auto PS In a previous post i mentioned a "floating point error" but this i hav...	alto_auto	7	2970	Nov 28, 2016 by ateszWRC
	How to erase suspend DTC of ECU Suzuki Carry without Diagnostic terminal (Preview) Dear Sirs, Please give me advice. My car is Suzuki Carry Truck without Diagnostic connector I could not turn off MIL even though that no DTC happen. Car running well, no problem but MIL still ON. Replace new ECU, MIL turn off normally. I do not know how to erase suspend DTC turn off the MIL. or check DTC o...	Phan	1	1381	Oct 24, 2016 by Phan
	Need pinouts for 33920-65G4 Ecm 1.3 Baleno -00 (Preview) Hello, i would need pinouts for this specific Ecm 33920-65G4 for my suzuki SJ410 engine swap, somehow i lost the largest obd1 A1 26pin connector but i managed to haul one from the junkyard and. Now i cant find any pinouts or repair manuals where to find electrical information for my proplem. Please h...	Bumingdeath	19	3406	Oct 20, 2016 by TechSupport
1 2 3 … 6 > Last» \| Page of 6 sorted by