RhinoPower Ltd

TechSupport · TechSupport

This is an ECU that came in with immo problems, although it came out of a 1.6 GV I've only found the part number on a J20 on the EPC. The 82D21 is listed as being for both the G16B and the J20 so Mitsubishi must have implemented some sort of dual mapping on these ECUs:

the alfer · the alfer

Just got the interface in by mail. Looking into finding out more about my Zuk. Especially the fault codes. Got the engine light sometimes coming on at 100 km/h (yes, only at that speed so far). Lifting my foot off the throttle a bit and it goes out. throttle back on and after a minute or so it comes back on. T...

xavier · xavier

Hello Rhinoman! greetings from Poland :) I have a small request. Could you draw injector drive output stage from some swift gti ecu ? (I think it should be all the same) If you're interested I can send you binaries and photos of F3 ecu. I've been poking around with its code in IDA Pro, found few things but w...

TOTech · TOTech

I have a 33920-56B40 that had C103 leak. The ECU is currently not working. When cleaning the board after removing the bad part, it became obvious that the trace between C103 & C1 had lifted and was damaged as well as C1 is lifting. The left side of C1 is still attached. http://www.rhinopower.org...

kostuch · kostuch

Hi, Can you help me to identify ecu, please? I've got this unit for free, but I know nothing about source. It was in chassis marked 33920-56B30 (vitara?), but connectors looks like from samurai? See the picture: http://pliczek.eu/images/694CIMG0317.jpg

tytower · tytower

May be in wrong section -please move as needed I would like to know what can be relied on to always work when faced with a car that won't start. Will the EFI injectors pump in fuel no matter what sensory data is not available ?Will a certain amount of fuel always be released on cranking Will the distributo...

zukjeff · zukjeff

jeff from Victoria , Australia. Electronics engineer , play with 8051, AVR and Bascom(basic). Looking for help and info to swap out a Carb,8v1600 with a 2000 16v sohc Baleno donk into a LWB sierra. the ECU is a 33920-65G9(1) 6N which is close to some on the web but i need to find accuate diagram/pin...

fierodough · fierodough

Hey guys! Need a bit of advice here... First off, can my ecu be flashed? (99 tracker 4x4 5spd 1.6L Canada) My ECU got water damaged... Long story... Water crossing failed... here is my ecu code: If it's not flashable... I managed to get an ECU from a 2.0L.. It's IDENTICAL same board and chips but a dif...

TechSupport · TechSupport

This ECU uses the same circuit board as the X90 of similar vintage, the firmware is the only difference. The additional board on this one has been fitted to eliminate the immobiliser - the ECU came to me because the company that fitted it made a complete hash of the job leaving the vehicle immobilised...

zukjeff · zukjeff

1995 Balino MT G16B with dizzy. ECU = 1453 6k 16 E24 339200-60GM-0 Denso 12v

zukjeff · zukjeff

Having troubles getting any good data on this ECM.. has anyone got a GM suzuki to worth ? connector has pins 4(gnd), 5(gnd), 7(K-line),16(+12),9(SDL)

Swifted · Swifted

Hey Guys, it's been a while since I have been on here, but I just had to come and show you what I came across recently. A JDM Cultus ECU Here are the Photos I took of it from every angle! I hope this can help with figuring out the differences... I'm gonna try hard to get it from the guy who loaned it to me.

Shadey · Shadey

Hi we are curently racing a baleno on short circuit and it is doing very well, now we have got to grips with set up we are in the hunt for more torque/power. We have to run standard ecu what i am looking for is there anyway to up the rev limiter by about 500rpm and increase the fuel this will be for a new engine ne...

TechSupport · TechSupport

This is a Wagon R ECU that I repaired a couple of years back, the processor is the Hitachi H8 as used in the Mitsubishi Vitara 16V models although the ECU is a far simpler (cheaper?) design. The WagonR was also manufactured as the Vauxhall Agila. http://www.rhinopower.org/ECUs/75FH0/images/pcb...

MIPS · MIPS

It all started with troubleshooting why this adapter was refusing to work between my ECU and the engine manager but when I accidenti...

tasos · tasos

hello i have a suzuki jimny 1.5 ddis the ecu is T6 delphi When the car tempurature goes over 89oC the fan doesnt start.... i check the coolant sensor, its ok...what else should i look...before go to ecu??

TechSupport · TechSupport

This ECU is going to be the development board for a Flash memory conversion for the 16V MAF based ECUs as fitted to the OBD1 Sidekick/Trackers/Vitaras and X90s. http://www.rhinopower.org/ECUs/79E50/79E50.html

misico · misico

I need repair o new ECU for suzuki alto 1.0L K10A NA 2WD 3AT part number 33920-76g8 the original is Hitachi Thacmks

TechSupport · TechSupport

Pics courtesy of Becs http://www.rhinopower.org/56B30/56B30.html

TechSupport · TechSupport

I can't remember what year Samurai this one is from but they all quite similar. The socketed processor is non-standard, this one was modified to take an EPROM conversion. http://www.rhinopower.org/ECUs/81C90/81C90.html

TechSupport · TechSupport

http://www.rhinopower.org/ECUs/56B80/56B80.html

jipooy · jipooy

Hello Guys, First a quick introduction of myself, I am a french frog exiled to Reunion island in Indian Ocean, closed to Madagascar. I lived for a year in Leeds and love your country guys. I guess that it is now, like France, too cold for me, love so much driving my Samurai only with its bikini

So I own a 2...

Juha · Juha

http://www.kolumbus.fi/juha.niinikoski/Suzuki_ECU/Suzuki_ECU.htm-- Edited by Rhinoman on Monday 22nd of February 2010 07:50:03 PM...

jqest · jqest

Hi Rhinoman, I'm trying with the ECU 33920-81CFO from a Suzuki Samurai 1.3 but didn't work. I found a spanish FSM that there is a serial link connection (conector de enlace de datos) on pin B15 but in my case the pin is not connected. I measured 5v on the pin, assembled your last schmatic BC847 and inverte...

TechSupport · TechSupport

http://www.rhinopower.org/ECUs/TCM_57B40/TCM_57B40.html-- Edited by Rhinoman on...

TechSupport · TechSupport

68HC916 based, reprogrammable, details to follow.

TechSupport · TechSupport

Transfered from the 68E40 thread: hepike wrote: Hi everyone, This is my first comment on this forum. First of all, this forum is amazing! There are a lot of useful knowlegde! --- Anyway... I have a Suzuki Swift 1.0 engine. I have every part of it except ECU wire. I want to buy a new one, or rebuild, becaus...

stomp120504 · stomp120504

Hi Guys Just wondering if this ECU can be remapped easily and if so where can I get the software to do it. I have an ODB2 USB conector. My car is the Grand Vitara gv1600 2004.

TechSupport · TechSupport

This ECU has been in the bottom of a box for a very long time. There are a few people playing with the H-series engines at present so I'm going to try and get this one running on the bench. The image below shows the ECU placed on top of a Canadian GV ECU, also from a H25 engined model. The two are very simila...

TechSupport · TechSupport

A slighly different one this time. A Bosch ECU for GV 2.0 Turbo Diesel :

Topic		Started By	Replies	Views	Last Post
	33920-82D20 Grand Vitara G16B? (Preview) This is an ECU that came in with immo problems, although it came out of a 1.6 GV I've only found the part number on a J20 on the EPC. The 82D21 is listed as being for both the G16B and the J20 so Mitsubishi must have implemented some sort of dual mapping on these ECUs:	TechSupport	0	3640	Nov 29, 2012 by TechSupport
	33920-77ED 0 TA11W 3-dr Escudo 2.0 V6 H20A A/T (Preview) Just got the interface in by mail. Looking into finding out more about my Zuk. Especially the fault codes. Got the engine light sometimes coming on at 100 km/h (yes, only at that speed so far). Lifting my foot off the throttle a bit and it goes out. throttle back on and after a minute or so it comes back on. T...	the alfer	36	6574	Nov 21, 2012 by goss
	swift gti injector drive circuit / F3 software (Preview) Hello Rhinoman! greetings from Poland :) I have a small request. Could you draw injector drive output stage from some swift gti ecu ? (I think it should be all the same) If you're interested I can send you binaries and photos of F3 ecu. I've been poking around with its code in IDA Pro, found few things but w...	xavier	4	1993	Oct 27, 2012 by TechSupport
	33920-56B30/40 Schematic and Component Identification (Preview) I have a 33920-56B40 that had C103 leak. The ECU is currently not working. When cleaning the board after removing the bad part, it became obvious that the trace between C103 & C1 had lifted and was damaged as well as C1 is lifting. The left side of C1 is still attached. http://www.rhinopower.org...	TOTech	5	4195	Sep 8, 2012 by kostuch
	Board identification (Preview) Hi, Can you help me to identify ecu, please? I've got this unit for free, but I know nothing about source. It was in chassis marked 33920-56B30 (vitara?), but connectors looks like from samurai? See the picture: http://pliczek.eu/images/694CIMG0317.jpg	kostuch	10	2522	Aug 22, 2012 by TechSupport
	Tutorial for the basics of ECU operation-what always works? (Preview) May be in wrong section -please move as needed I would like to know what can be relied on to always work when faced with a car that won't start. Will the EFI injectors pump in fuel no matter what sensory data is not available ?Will a certain amount of fuel always be released on cranking Will the distributo...	tytower	8	3807	Aug 14, 2012 by yknot
	33920-65G91 Baleno 1.6 to go into a sierra. (Preview) jeff from Victoria , Australia. Electronics engineer , play with 8051, AVR and Bascom(basic). Looking for help and info to swap out a Carb,8v1600 with a 2000 16v sohc Baleno donk into a LWB sierra. the ECU is a 33920-65G9(1) 6N which is close to some on the web but i need to find accuate diagram/pin...	zukjeff	41	8388	Jun 21, 2012 by TechSupport
	Water damaged 99 Tracker 1.6l ECU swap with 2.0L ECU. (Preview) Hey guys! Need a bit of advice here... First off, can my ecu be flashed? (99 tracker 4x4 5spd 1.6L Canada) My ECU got water damaged... Long story... Water crossing failed... here is my ecu code: If it's not flashable... I managed to get an ECU from a 2.0L.. It's IDENTICAL same board and chips but a dif...	fierodough	1	1772	May 29, 2012 by TechSupport
	33920-71EE0 1997 Vitara 1.6 16V (Preview) This ECU uses the same circuit board as the X90 of similar vintage, the firmware is the only difference. The additional board on this one has been fitted to eliminate the immobiliser - the ECU came to me because the company that fitted it made a complete hash of the job leaving the vehicle immobilised...	TechSupport	6	5556	Apr 18, 2012 by TechSupport
	33920-60GM (Preview) 1995 Balino MT G16B with dizzy. ECU = 1453 6k 16 E24 339200-60GM-0 Denso 12v	zukjeff	3	1495	Apr 16, 2012 by TechSupport
	33920-70H2 M15A AWD Ignis ( 2002 GM Cruze) (Preview) Having troubles getting any good data on this ECM.. has anyone got a GM suzuki to worth ? connector has pins 4(gnd), 5(gnd), 7(K-line),16(+12),9(SDL)	zukjeff	8	1997	Apr 11, 2012 by TechSupport
	33920-64B6 3 - Suzuki Swift Cultus F6 (JDM spec) (Preview) Hey Guys, it's been a while since I have been on here, but I just had to come and show you what I came across recently. A JDM Cultus ECU Here are the Photos I took of it from every angle! I hope this can help with figuring out the differences... I'm gonna try hard to get it from the guy who loaned it to me.	Swifted	17	10457	Mar 14, 2012 by TechSupport
	Baleno 16v ( 1 2 ) (Preview) Hi we are curently racing a baleno on short circuit and it is doing very well, now we have got to grips with set up we are in the hunt for more torque/power. We have to run standard ecu what i am looking for is there anyway to up the rev limiter by about 500rpm and increase the fuel this will be for a new engine ne...	Shadey	51	14695	Feb 23, 2012 by A10warlord
	33920-75FH0 1998 Wagon R K12A (Preview) This is a Wagon R ECU that I repaired a couple of years back, the processor is the Hitachi H8 as used in the Mitsubishi Vitara 16V models although the ECU is a far simpler (cheaper?) design. The WagonR was also manufactured as the Vauxhall Agila. http://www.rhinopower.org/ECUs/75FH0/images/pcb...	TechSupport	0	1667	Jan 29, 2012 by TechSupport
	GEO 33920-56B30 ECU Trace Diagram (Preview) It all started with troubleshooting why this adapter was refusing to work between my ECU and the engine manager but when I accidenti...	MIPS	12	5331	Jan 25, 2012 by TechSupport
	jimny 33920-84A10 (Preview) hello i have a suzuki jimny 1.5 ddis the ecu is T6 delphi When the car tempurature goes over 89oC the fan doesnt start.... i check the coolant sensor, its ok...what else should i look...before go to ecu??	tasos	6	2599	Jan 16, 2012 by TechSupport
	33920-79E50 X90 1.6 16V (Preview) This ECU is going to be the development board for a Flash memory conversion for the 16V MAF based ECUs as fitted to the OBD1 Sidekick/Trackers/Vitaras and X90s. http://www.rhinopower.org/ECUs/79E50/79E50.html	TechSupport	0	2021	Jan 16, 2012 by TechSupport
	ecu part number 33920-76g8 (Preview) I need repair o new ECU for suzuki alto 1.0L K10A NA 2WD 3AT part number 33920-76g8 the original is Hitachi Thacmks	misico	1	1247	Dec 1, 2011 by TechSupport
	33920-56B30 1992 Sidekick 1.6 8V (Preview) Pics courtesy of Becs http://www.rhinopower.org/56B30/56B30.html	TechSupport	0	1975	Nov 13, 2011 by TechSupport
	33920-81C90 Samurai 1.3 TBI 199? (Preview) I can't remember what year Samurai this one is from but they all quite similar. The socketed processor is non-standard, this one was modified to take an EPROM conversion. http://www.rhinopower.org/ECUs/81C90/81C90.html	TechSupport	0	2599	Nov 12, 2011 by TechSupport
	33920-56B80 Vitara1.6 8V 1992 Auto (Preview) http://www.rhinopower.org/ECUs/56B80/56B80.html	TechSupport	1	4037	Nov 12, 2011 by TechSupport
	33920-80CQ SAMURAI 1.3i (G13BB) 2003 (Preview) Hello Guys, First a quick introduction of myself, I am a french frog exiled to Reunion island in Indian Ocean, closed to Madagascar. I lived for a year in Leeds and love your country guys. I guess that it is now, like France, too cold for me, love so much driving my Samurai only with its bikini So I own a 2...	jipooy	4	5064	Nov 12, 2011 by jipooy
	Swift 8V 33920-63B7 Denso D3 (Preview) http://www.kolumbus.fi/juha.niinikoski/Suzuki_ECU/Suzuki_ECU.htm-- Edited by Rhinoman on Monday 22nd of February 2010 07:50:03 PM...	Juha	5	5056	Oct 28, 2011 by TechSupport
	33920-81CF0 Samurai 1997 (Preview) Hi Rhinoman, I'm trying with the ECU 33920-81CFO from a Suzuki Samurai 1.3 but didn't work. I found a spanish FSM that there is a serial link connection (conector de enlace de datos) on pin B15 but in my case the pin is not connected. I measured 5v on the pin, assembled your last schmatic BC847 and inverte...	jqest	9	3986	Oct 26, 2011 by TechSupport
	38880-57B40 Vitara TCM (Preview) http://www.rhinopower.org/ECUs/TCM_57B40/TCM_57B40.html-- Edited by Rhinoman on...	TechSupport	2	3485	Oct 17, 2011 by fordem
	33920-68E40 Swift, 1.0L, 2001 (Preview) 68HC916 based, reprogrammable, details to follow.	TechSupport	2	3959	Jul 20, 2011 by TechSupport
	33920-68E00 2001 Swift 1.0 3cyl (Preview) Transfered from the 68E40 thread: hepike wrote: Hi everyone, This is my first comment on this forum. First of all, this forum is amazing! There are a lot of useful knowlegde! --- Anyway... I have a Suzuki Swift 1.0 engine. I have every part of it except ECU wire. I want to buy a new one, or rebuild, becaus...	TechSupport	0	2410	Jul 20, 2011 by TechSupport
	33920-50J20 Grand Vitara GV1600 2004 (Preview) Hi Guys Just wondering if this ECU can be remapped easily and if so where can I get the software to do it. I have an ODB2 USB conector. My car is the Grand Vitara gv1600 2004.	stomp120504	8	3925	Jul 13, 2011 by stomp120504
	33920-67D60 GV H25 EC MT (Preview) This ECU has been in the bottom of a box for a very long time. There are a few people playing with the H-series engines at present so I'm going to try and get this one running on the bench. The image below shows the ECU placed on top of a Canadian GV ECU, also from a H25 engined model. The two are very simila...	TechSupport	0	3532	Jul 5, 2011 by TechSupport
	33920-67G00 GV 2.0 Turbo Diesel (Preview) A slighly different one this time. A Bosch ECU for GV 2.0 Turbo Diesel :	TechSupport	0	2479	Apr 19, 2011 by TechSupport
«First < 1 … 4 5 6 \| Page of 6 sorted by