RhinoPower Ltd

TechSupport · TechSupport

RhinoPower Ltd is working on an interface for ECUs that use the SDL/KWP interface, this is the format typically used on OBD1 Suzukis worldwide from 2001 up until approx 2010 when CANBus was introduced globally. SDL/KWP is a proprietary implementation of the KWP2000 protocol.

madmaxarjun · madmaxarjun

Hi all, I have been trying to sort out a flat spot issue I have had for quite some time. We went through all the sensors and everthing seems to be in spec. While troubleshooting the issue, the TPS grabbed my attention, though the voltage seem to in the defined limits, I was not able to read over 3.6 volts at ...

archat68 · archat68

I have a Maruti Suzuki Swift diesel 2007 which has a OBDII connector. But everybody failed to get the Scangauge working with it. The service manual says that the pin no. 7 (K line - ISO 9141) is used to communiacte with Suzuki scantool. Also, the ECU uses 2 sockets to connect with the vehicle. Here are are...

TechSupport · TechSupport

I am aware from emails and from reading posts on Teambhp that there are a lot of problems with Suzuki/Marutis vehicles. Currently India mandates Euro emissions levels, OBD1 is mandated from October 2010 and OBD2 from 2013. I have set up this sub-forum in the hope of collating information regarding...

zaks · zaks

Hi, I own a Maruti Suzuki Baleno 1.3 Diesel (FIAT sourced MultiJet Engine), I am trying to confirm the protocol used in my Vehicle, being a 2016 Vehicle it is OBD2 compliant, and ELM327 scan showed that it uses KWP FAST init (ISO14230-4) protocol, my query is that is the ECU data transmitted in K-Line (...

aashishkul · aashishkul

Hi, I own a Maruti Suzuki Wagon R (India) with 33920-79FS ECU. ECU is manufactured by Denso. I would like to read engine parameters. I have read about ALDL protocol and hardware required for reading it. I have some questions- 1. Does this ECU support ALDL/ OBD-I protocol or OBD-II? 2. Can you give me a...

go88go88com · go88go88com

Nhà cái GO88 tập trung phát triển mảng giải trí trực tuyến tại Việt Nam với danh mục gồm game bài, casino, bắn cá, nổ hũ và nhiều trò chơi khác. GO 88 được định hình như một hệ sinh thái game online đa dạng, giúp người dùng dễ tìm kiếm nội dung phù hợp. Trang GO88 tiếp tục mở rộng sản phẩm để gia tăng lựa chọn cho cộn...

chandra · chandra

Hi, My 2007 alto has the OBD II connector port. I can initiate a connection using the ISO 14320-4 KWP protocol using the ELM based scanner. I also increased the ELM timeout to almost 1 second. However, the only response I get for any command is 7F xx xx. Is there a possibility that the interface uses the s...

Mirach · Mirach

I didn't find it on the site, is it possible to buy an sdl interface? My girlfriend recently bought a Vitare 1.6 16v from 1994, Europe version. Now the car lacks power, the diagnosis does not give any errors and we are struggling to understand the problem. There is a 6-pin connector in the engine compart...

suzukitas · suzukitas

Trying to get this XL7 back on the road, and engine light is coming on. On bringing diagnostic connector, it will randomly throw codes: 17(not listed) 16(not listed) 15(continuous blinks)(150?) and on occasion a solid(ecu error) The car itself seems to drive/run as it should and shows no issues th...

rivargut · rivargut

Hi ! I found your website regarding communication with Suzuki ECUs. In my case I have a Jimny 2014 in Costa Rica. I am programming my own device to get fuel consumption, and looking into PIDs as RPM, Speed, IAT and MAP. Looking into its OBD2 port, it only has GND/12V and KWP pin 7 (Kline). I had a couple s...

sknawni · sknawni

Hi All..! I have a G13BB Engine mounted and running on a fabricated chassis which was taken out of a Maruti-Suzuki Esteem VXi from year 2007. The ECM / PCM details are as follows: ECM / PCM: 33920-66ES Euro - 3 Make: Denso (India) This engine is being used to check the efficiency and meaningfulness of a h...

nanhi99 · nanhi99

Hi rhinoman AC for swift petrol ( India) is not working despite of changing cars ecm is AC connected to anything like BCM? iwas told that bcm could be bad can you please throw some light on this issue ? if possible how can I check BCM

zohar · zohar

I am trying to read the VIN number of my Volvo by sending 09 02 command and I am getting 83 F1 11 7F 09 11 1E as an answer to all 09 mode commands 01 mode is working OK

skpadala · skpadala

Hi all My car is Maruti Alto K10 (with K10 engine) manufactured in India in 2011, and having 16 pin connector to check DTC. Pin nos 4,5,6,7, 14 & 16 populated. Does the USB SDL interface & Rhinoview works with my car? or any other which are suitable pl advice.

nanhi99 · nanhi99

I have a Maruti Alto 2001 vxi car ( with wagon R engine)how can I use the scanner or software for diagnosing problems?I can buy cable or connector provided it works with my car

Sambuddha · Sambuddha

Hi, i have been reading the posts on your forum, i happen to have a Suzuki swift 2006 model. I bought a autel maxi-scan 509, the device connected, and identified the protocol as KWP2000, but i couldnt get any reading off it. was wonder if there is any way to get reading of it? including read and clear error...

IndrojitSircar · IndrojitSircar

Hi guys, i picked up a 1.6 Euro III baleno engine from a scrapper a couple of days back with the ECU and Wiring from the ECU to the Engine. Now on the ECU end of the wiring i find there are 3 couplers. Out of which only two which are white in colour fit the ECU and i am left with one more coupler that is much bigger a...

TechSupport · TechSupport

If anyone has a source for Indian market ECUs for a reasonable cost please PM me with details. It will help with discovering what protocols are in use. Thanks James

Subhash · Subhash

HI, Like old model wagon R,the monitor terminal (Socket) inside fuse/relay box in engine room is not used in Euro3 model. Also On board dignostic is SDT and not OBD1orOBD2.Is there any way to find error code in new model(Euro 3) by connecting a jumper between two terminals? Maruti service centre peo...

Subhash · Subhash

In the speedometer eprom bin file.where does the odometer data saved? is it possible to edit that data with eprom programmer like Elnec programmer? Thanks and regards

Topic		Started By	Replies	Views	Last Post
	STICKY: SDL/KWP protocol (Preview) RhinoPower Ltd is working on an interface for ECUs that use the SDL/KWP interface, this is the format typically used on OBD1 Suzukis worldwide from 2001 up until approx 2010 when CANBus was introduced globally. SDL/KWP is a proprietary implementation of the KWP2000 protocol.	TechSupport	45	18191	Sep 21, 2025 by mosquito
	TPS info for baleno G16b Euro II (Preview) Hi all, I have been trying to sort out a flat spot issue I have had for quite some time. We went through all the sensors and everthing seems to be in spec. While troubleshooting the issue, the TPS grabbed my attention, though the voltage seem to in the defined limits, I was not able to read over 3.6 volts at ...	madmaxarjun	21	6993	1h ago by ipimoj11
	Maruti Suzuki Swift Diesel - which protocol? (Preview) I have a Maruti Suzuki Swift diesel 2007 which has a OBDII connector. But everybody failed to get the Scangauge working with it. The service manual says that the pin no. 7 (K line - ISO 9141) is used to communiacte with Suzuki scantool. Also, the ECU uses 2 sockets to connect with the vehicle. Here are are...	archat68	43	18445	10 days ago by cosave7904
	Diagnostics in India (Preview) I am aware from emails and from reading posts on Teambhp that there are a lot of problems with Suzuki/Marutis vehicles. Currently India mandates Euro emissions levels, OBD1 is mandated from October 2010 and OBD2 from 2013. I have set up this sub-forum in the hope of collating information regarding...	TechSupport	22	8874	September 30th by cosave7904
	OBD Protocol - Maruti Suzuki Baleno Hatch 1.3 Diesel 2016 Model (Preview) Hi, I own a Maruti Suzuki Baleno 1.3 Diesel (FIAT sourced MultiJet Engine), I am trying to confirm the protocol used in my Vehicle, being a 2016 Vehicle it is OBD2 compliant, and ELM327 scan showed that it uses KWP FAST init (ISO14230-4) protocol, my query is that is the ECU data transmitted in K-Line (...	zaks	1	2675	September 29th by yelatab
	33920-79FS ECU- Maruti Suzuki Wagon R Euro 3 ECU (Preview) Hi, I own a Maruti Suzuki Wagon R (India) with 33920-79FS ECU. ECU is manufactured by Denso. I would like to read engine parameters. I have read about ALDL protocol and hardware required for reading it. I have some questions- 1. Does this ECU support ALDL/ OBD-I protocol or OBD-II? 2. Can you give me a...	aashishkul	47	27958	September 29th by yelatab
	go88go88com (Preview) Nhà cái GO88 tập trung phát triển mảng giải trí trực tuyến tại Việt Nam với danh mục gồm game bài, casino, bắn cá, nổ hũ và nhiều trò chơi khác. GO 88 được định hình như một hệ sinh thái game online đa dạng, giúp người dùng dễ tìm kiếm nội dung phù hợp. Trang GO88 tiếp tục mở rộng sản phẩm để gia tăng lựa chọn cho cộn...	go88go88com	0	54	September 27th by go88go88com
	OBD in 2007 alto (Preview) Hi, My 2007 alto has the OBD II connector port. I can initiate a connection using the ISO 14320-4 KWP protocol using the ELM based scanner. I also increased the ELM timeout to almost 1 second. However, the only response I get for any command is 7F xx xx. Is there a possibility that the interface uses the s...	chandra	9	10397	September 27th by yelatab
	Buy sdl interface (Preview) I didn't find it on the site, is it possible to buy an sdl interface? My girlfriend recently bought a Vitare 1.6 16v from 1994, Europe version. Now the car lacks power, the diagnosis does not give any errors and we are struggling to understand the problem. There is a 6-pin connector in the engine compart...	Mirach	0	1378	Jun 17, 2025 by Mirach
	unknown fault codes ; 2002 A/T XL7 16 17 15(continuous) ecu fault codes 15 16 17 xl7 h27a suzuki grand vitara ja627 (Preview) Trying to get this XL7 back on the road, and engine light is coming on. On bringing diagnostic connector, it will randomly throw codes: 17(not listed) 16(not listed) 15(continuous blinks)(150?) and on occasion a solid(ecu error) The car itself seems to drive/run as it should and shows no issues th...	suzukitas	6	2798	Mar 29, 2021 by TonyXL7
	KWP protocol for Suzuki Jimny 2014 (Preview) Hi ! I found your website regarding communication with Suzuki ECUs. In my case I have a Jimny 2014 in Costa Rica. I am programming my own device to get fuel consumption, and looking into PIDs as RPM, Speed, IAT and MAP. Looking into its OBD2 port, it only has GND/12V and KWP pin 7 (Kline). I had a couple s...	rivargut	0	2546	Aug 10, 2020 by rivargut
	Can RV read this G13BB ECM / PCM (Preview) Hi All..! I have a G13BB Engine mounted and running on a fabricated chassis which was taken out of a Maruti-Suzuki Esteem VXi from year 2007. The ECM / PCM details are as follows: ECM / PCM: 33920-66ES Euro - 3 Make: Denso (India) This engine is being used to check the efficiency and meaningfulness of a h...	sknawni	1	3359	Feb 26, 2018 by TechSupport
	AC of swift petrol not working (Preview) Hi rhinoman AC for swift petrol ( India) is not working despite of changing cars ecm is AC connected to anything like BCM? iwas told that bcm could be bad can you please throw some light on this issue ? if possible how can I check BCM	nanhi99	1	3757	Jun 22, 2015 by TechSupport
	reading volvo VIN number (Preview) I am trying to read the VIN number of my Volvo by sending 09 02 command and I am getting 83 F1 11 7F 09 11 1E as an answer to all 09 mode commands 01 mode is working OK	zohar	3	3397	Mar 12, 2014 by TechSupport
	Maruti Alto K10 DTC (Preview) Hi all My car is Maruti Alto K10 (with K10 engine) manufactured in India in 2011, and having 16 pin connector to check DTC. Pin nos 4,5,6,7, 14 & 16 populated. Does the USB SDL interface & Rhinoview works with my car? or any other which are suitable pl advice.	skpadala	2	4543	Oct 19, 2012 by skpadala
	scanning indian cars (Preview) I have a Maruti Alto 2001 vxi car ( with wagon R engine)how can I use the scanner or software for diagnosing problems?I can buy cable or connector provided it works with my car	nanhi99	17	6128	Sep 24, 2012 by nanhi99
	2006 Maruti Suzuki OBDII readings (Preview) Hi, i have been reading the posts on your forum, i happen to have a Suzuki swift 2006 model. I bought a autel maxi-scan 509, the device connected, and identified the protocol as KWP2000, but i couldnt get any reading off it. was wonder if there is any way to get reading of it? including read and clear error...	Sambuddha	1	4412	Aug 20, 2012 by TechSupport
	Baleno Euro III wiring query (Preview) Hi guys, i picked up a 1.6 Euro III baleno engine from a scrapper a couple of days back with the ECU and Wiring from the ECU to the Engine. Now on the ECU end of the wiring i find there are 3 couplers. Out of which only two which are white in colour fit the ECU and i am left with one more coupler that is much bigger a...	IndrojitSircar	5	4835	Aug 4, 2011 by mclaren1885
	Indian ECUs (closed) (Preview) If anyone has a source for Indian market ECUs for a reasonable cost please PM me with details. It will help with discovering what protocols are in use. Thanks James	TechSupport	0	4644	Nov 12, 2010 by TechSupport
	MARUTI-SUZUKI wagon R EURO3 (Preview) HI, Like old model wagon R,the monitor terminal (Socket) inside fuse/relay box in engine room is not used in Euro3 model. Also On board dignostic is SDT and not OBD1orOBD2.Is there any way to find error code in new model(Euro 3) by connecting a jumper between two terminals? Maruti service centre peo...	Subhash	1	4616	Sep 23, 2010 by TechSupport
	Alto(Maruti Suzuki) (Preview) In the speedometer eprom bin file.where does the odometer data saved? is it possible to edit that data with eprom programmer like Elnec programmer? Thanks and regards	Subhash	2	4640	Aug 13, 2010 by Subhash
Page 1 of 1 sorted by