RhinoPower Ltd

iluvator · iluvator

Hi, I just purchased the SDL interface and here is what happens when I connect it with my win 7 64bit laptop: SDL interface is recognized by the software and communication can be established using 15625 baud. But after a couple of seconds bad data count begins and there is no values updating thereafter...

Alexandr · Alexandr

Hello, the problem is not only me but also many ... where can I find information on decoding program rhino power? data on work. it was possible to see immediately what the problem is. I personally did notable all sensors translate to your language and denomination for many not found. thanks in advance...

liviurene · liviurene

Hi all, I'm Liviu from Romania. Just curious, is the forum and RhinoPower active? It is in my intention to buy an interface for my Suzuki Jimny 1999- 1298cc: VIN: JSAFJB33V00 101940 and to use it with a laptop Win7. It is stil availabe? Will it work for my Jimny? Thank you.

igor · igor

First of all - many thanks for the software & cable!! With the ign ON, engine OFF and full throttle the TPS shows 84% only. Physically I don't see any way to open it further.. Is this indication 'normal'? tanks, Igor

Zackman · Zackman

Dear Guru: Added to my sever frustration with my Sidekick, yesterday, the Windows tablet that was running the R-V software started its automatic upgrading, and unfortunately during upgrading its power went down and now cannot start (stock at 35% upgrade stage and cannot boot). At that stage, I in...

pancho · pancho

I´m trying to connect to ECU, my question is which are in windows XP the preferred settings for the com port: Speed bits per second= data bits qty= parity = stop bits= flux control= or is the communication between XP and Interfase settings automatic?

Zackman · Zackman

Dear Guru: Forgive my naïvety; but I have two questions: 1) Can the software be used to change the timing (i.e., say if timing is at 10 deg BTDC, move it to 8 deg BTDC?). 2) Moreover, can teh software be used to test the health of the ECU (i.e., whether there is anything wrong with the ECU)? Thank you for y...

Zackman · Zackman

Hi: I am new here. I bouught the Rhino OBDI for my 91 Sidekick. I put a used engine in the car. It starts and runs reasonably OK, but when I try to put it in gear, it dies. If I keep foot on the accelerator it run, but with very low power, dispute the fact that compression test gives a minimum of 155 psi for ea...

PsyCro · PsyCro

So, my SDL interface is on its way soon, and my new used car is off to the mechanic soon as well for some general upkeep. Having my CV boots done, 5w30 oil and filter, diff and trans case oil, and new oil pan gasket since its leaking. Don't know yet if the mech will be pulling the differential to get to the oil p...

TechSupport · TechSupport

RhinoView v1.1 is released. http://www.rhinopower.org/Rhinoview/release/RhinoviewV1_1.zip The definition file for the 1202 ECU has been fixed The USB handler has been modified. The initialisation file for the dashboard was corrupted and has been fixed The help files have been updated fo...

robert finch · robert finch

I am trying to get Rhinoview to talk to the ECU on my Suzuki Grand Vitara XL7, V6 2.7L 2001. The ECU number is 33920-52D9. The connector is a 16 pin with wires on pins 4, 5 7, 9 and 16. Upon following the help guide I can get it to say "Connected to ECU" but the dashboard is blank with no informa...

Pilotpete · Pilotpete

I have been trying for several days to get the cable I got from OBD Diagnostics Inc to work with my Rhinoviewer. I Tried just hooking it up, no luck. I tried downloading and installing the virtual Com driver the Rhinopower web site says it needs but still no luck. The program also does not have the Comm...

Kentm111 · Kentm111

Hi, brought a kit from you a while ago and used it on an older laptop with no significant issues. Now using a more "modern" laptop but I cannot get Rhinoview to connect to the ecu. Under comms I do not have the "settings" that the help file refers to. Im not too sure if this is helpfu...

rcx036 · rcx036

Hi, just received my SDL interface kit. I'm on Windows 7. I installed the latest 64-bit Windows driver. Then installed RhinoView, but Rhinoview would not start as detailed in another post. I then downloaded the FTD2XX.DLL to the Rhinoview root folder, as advised in previous post. But all I get is try...

rcx036 · rcx036

I've installed the D2XX driver version 2.12.06. Then installed RhinoView. When I run I get "program can't start because FTD2XX.DLL is missing". I imagine this is because I've installed the 64-bit driver and Rhinoview is a 32 bit only application? If so then should I give VMPlayer a go to...

HTViking · HTViking

TechSupport wrote: On the early models open/closed loop status is called O2S Active. RPM control will only work if the vehicle is stationary with the idle switch closed and the engine at normal operating temperature. The reset ECU function is not very well documented by Suzuki, I look at that again...

Hans ole · Hans ole

Hello everybody, i need som help please. the program works fine for 10 sec and then it just stops and bad data count starts counting. does anybody know why this happenes?

bmentink · bmentink

Hi There, I would like to use the software but don't use windoz machines, rather use Linux. Is there any chance of a Linux port? Or failing that ... would it run under wine?

TechSupport · TechSupport

I have been made aware of issues with the definition for the Track/Kick/Vit 16V 1202 ECU. I erroneously used the definition for the never released 1995 'OBD2' ECU, I'm working on fixing that and will release a new build of RV. If you think you have problems with one of these ECUs then please contact me...

SwingDancer · SwingDancer

Can someone please help me? I have a 1994 Geo Metro XFi (Standard Emissions) (California Emissions) ECU: B7 3-ER-CAL 33920-60E54 OBD Diagnostics, Inc. ALDL (GM OBD1) Cable with 12 pin SDL Connector to USB I get about 5 volts across M to A pins and about 12 volts across H to A pins MIL functions prop...

randy h · randy h

Is there config file or setting I can tweak to get a different sized window from Rhinoview? My Car PC's Monitor has a native resolution of 800 x 600. I cant seem to get a good view of Rhinoview. I have to move the window around to see the edges. thanks, randy H

moonraker · moonraker

Hi Rhinoman, Hi Forum! I'm new here today and very very excited what this Project is about, this is great stuff Rhinoman! So first about me: I'm from Germany and my car is a '92 Swift EA 1.0, at the moment barely 80.000km. Very few problems so far (New Battery, new tail exhause pipe) but now he's running in...

wagonR+ · wagonR+

Please help, I am using the RhinoPower USB OBD1 cable and trying to connect to my petrol Wagon R+ using an Msi Wind netbook running XP. Cable shows up in Device manager on comm11 so I have set that in RhinoView, tried both speeds to no effect. Any ideas please.

sean952 · sean952

Hi I have a 2000 vitara 4u2 with no spark or fuel ran perfect then all of a sudden this. now my dash lights have gone too but car will still turn over ???????? please can any one help.

rcullens · rcullens

Hi all, I was wondering what all diags or software I would be able to do on my xl-7. Its a 2001 American version, also what cables would I need to iinterface... Thanks in advance, Roger

quangtruong · quangtruong

What the Relationship between ECU part number and ECU Identification? in the picture below, the ECU part number is 33920-80GA0 , what is the ECU IDs of this module, is 33920-80GA ? please give me some advice. thanks,

madmaxarjun · madmaxarjun

Hello, Just received my cable, Thank you!. Tried hooking it up to an Indian SX4, though 2007 this ECU is certainly not OBD II complaint. the software keeps saying "bad data count" I suspect this relates to reading from the ECU. Here is a pic of the port, comparing this to the standard OB...

randy h · randy h

Is there a particular sensor data set I can observe in Rhinoview that would confirm if my engine is running in Closed Loop? Its probably obvious but I cant figure out. thanks randy

fordem · fordem

TPS - I seem to have three addresses #11, #12 & #38 - this is a 3 wire TPS by the way Throttle closed #11 is at 0, #12 is at 31, and #38 is at 16 - as the throttle is opened 11 & 12 increase gradually until at max throttle 11 is at 172 and 12 is at 204 - note that at max throttle the difference is also 31, this d...

tslight · tslight

hi there my name is tristan slight i live in western australia, australia i have a 2007 Suzuki jimny m13a vvt which i currently converted to a m18a engine everything went fine and ran well it has since done about 2000km. Today the engine light come on but still runs fine the only thing i have noticed is tha...

Topic		Started By	Replies	Views	Last Post
	Vitara 1993 8v bad data count (Preview) Hi, I just purchased the SDL interface and here is what happens when I connect it with my win 7 64bit laptop: SDL interface is recognized by the software and communication can be established using 15625 baud. But after a couple of seconds bad data count begins and there is no values updating thereafter...	iluvator	5	1884	Mar 17, 2016 by TechSupport
	decrypting data (Preview) Hello, the problem is not only me but also many ... where can I find information on decoding program rhino power? data on work. it was possible to see immediately what the problem is. I personally did notable all sensors translate to your language and denomination for many not found. thanks in advance...	Alexandr	2	1751	Mar 14, 2016 by Alexandr
	Is the forum and RhinoPower stil active? (Preview) Hi all, I'm Liviu from Romania. Just curious, is the forum and RhinoPower active? It is in my intention to buy an interface for my Suzuki Jimny 1999- 1298cc: VIN: JSAFJB33V00 101940 and to use it with a laptop Win7. It is stil availabe? Will it work for my Jimny? Thank you.	liviurene	2	1864	Mar 14, 2016 by liviurene
	TPS full open shows 84% (Preview) First of all - many thanks for the software & cable!! With the ign ON, engine OFF and full throttle the TPS shows 84% only. Physically I don't see any way to open it further.. Is this indication 'normal'? tanks, Igor	igor	2	1517	Feb 26, 2016 by igor
	The good 'ol no"not able to communicate" issue! (Preview) Dear Guru: Added to my sever frustration with my Sidekick, yesterday, the Windows tablet that was running the R-V software started its automatic upgrading, and unfortunately during upgrading its power went down and now cannot start (stock at 35% upgrade stage and cannot boot). At that stage, I in...	Zackman	8	1754	Feb 17, 2016 by TechSupport
	Com Port settings? (Preview) I´m trying to connect to ECU, my question is which are in windows XP the preferred settings for the com port: Speed bits per second= data bits qty= parity = stop bits= flux control= or is the communication between XP and Interfase settings automatic?	pancho	5	2587	Feb 7, 2016 by TechSupport
	Can timing be changed by the software? (Preview) Dear Guru: Forgive my naïvety; but I have two questions: 1) Can the software be used to change the timing (i.e., say if timing is at 10 deg BTDC, move it to 8 deg BTDC?). 2) Moreover, can teh software be used to test the health of the ECU (i.e., whether there is anything wrong with the ECU)? Thank you for y...	Zackman	2	1406	Feb 3, 2016 by Zackman
	Average values reported by the Rhino OBDI tool (Preview) Hi: I am new here. I bouught the Rhino OBDI for my 91 Sidekick. I put a used engine in the car. It starts and runs reasonably OK, but when I try to put it in gear, it dies. If I keep foot on the accelerator it run, but with very low power, dispute the fact that compression test gives a minimum of 155 psi for ea...	Zackman	4	1515	Feb 2, 2016 by Zackman
	Off to the mech.. (Preview) So, my SDL interface is on its way soon, and my new used car is off to the mechanic soon as well for some general upkeep. Having my CV boots done, 5w30 oil and filter, diff and trans case oil, and new oil pan gasket since its leaking. Don't know yet if the mech will be pulling the differential to get to the oil p...	PsyCro	0	1099	Jan 25, 2016 by PsyCro
	RhinoView v1.1 is released (Preview) RhinoView v1.1 is released. http://www.rhinopower.org/Rhinoview/release/RhinoviewV1_1.zip The definition file for the 1202 ECU has been fixed The USB handler has been modified. The initialisation file for the dashboard was corrupted and has been fixed The help files have been updated fo...	TechSupport	6	2574	Jan 20, 2016 by TechSupport
	Trying to connect to ECU on a Grand Vitara XL7 2001 (Preview) I am trying to get Rhinoview to talk to the ECU on my Suzuki Grand Vitara XL7, V6 2.7L 2001. The ECU number is 33920-52D9. The connector is a 16 pin with wires on pins 4, 5 7, 9 and 16. Upon following the help guide I can get it to say "Connected to ECU" but the dashboard is blank with no informa...	robert finch	4	1572	Jan 8, 2016 by robert finch
	Can't get ALDL cable to work (Preview) I have been trying for several days to get the cable I got from OBD Diagnostics Inc to work with my Rhinoviewer. I Tried just hooking it up, no luck. I tried downloading and installing the virtual Com driver the Rhinopower web site says it needs but still no luck. The program also does not have the Comm...	Pilotpete	1	1395	Nov 29, 2015 by TechSupport
	Connecting problems - Cannot connect to the ECU - HELP!! (Preview) Hi, brought a kit from you a while ago and used it on an older laptop with no significant issues. Now using a more "modern" laptop but I cannot get Rhinoview to connect to the ecu. Under comms I do not have the "settings" that the help file refers to. Im not too sure if this is helpfu...	Kentm111	3	1100	Oct 30, 2015 by TechSupport
	Trying to connect - 1997 Vitara 16v (Preview) Hi, just received my SDL interface kit. I'm on Windows 7. I installed the latest 64-bit Windows driver. Then installed RhinoView, but Rhinoview would not start as detailed in another post. I then downloaded the FTD2XX.DLL to the Rhinoview root folder, as advised in previous post. But all I get is try...	rcx036	4	1239	Aug 18, 2015 by rcx036
	FTD2XX.DLL missing (Preview) I've installed the D2XX driver version 2.12.06. Then installed RhinoView. When I run I get "program can't start because FTD2XX.DLL is missing". I imagine this is because I've installed the 64-bit driver and Rhinoview is a 32 bit only application? If so then should I give VMPlayer a go to...	rcx036	1	1110	Aug 17, 2015 by TechSupport
	Some question about RhinoPower software (Preview) TechSupport wrote: On the early models open/closed loop status is called O2S Active. RPM control will only work if the vehicle is stationary with the idle switch closed and the engine at normal operating temperature. The reset ECU function is not very well documented by Suzuki, I look at that again...	HTViking	0	899	Jul 21, 2015 by HTViking
	97 Baleno bad data count (Preview) Hello everybody, i need som help please. the program works fine for 10 sec and then it just stops and bad data count starts counting. does anybody know why this happenes?	Hans ole	7	1091	Apr 17, 2015 by Hans ole
	Linux port? (Preview) Hi There, I would like to use the software but don't use windoz machines, rather use Linux. Is there any chance of a Linux port? Or failing that ... would it run under wine?	bmentink	1	787	Feb 3, 2015 by TechSupport
	issues with the track/Kick 1202 definition (Preview) I have been made aware of issues with the definition for the Track/Kick/Vit 16V 1202 ECU. I erroneously used the definition for the never released 1995 'OBD2' ECU, I'm working on fixing that and will release a new build of RV. If you think you have problems with one of these ECUs then please contact me...	TechSupport	34	2092	Aug 31, 2014 by cosmic_splatter
	Cannot get RhinoView V1.0 to connect to SDL interface (Preview) Can someone please help me? I have a 1994 Geo Metro XFi (Standard Emissions) (California Emissions) ECU: B7 3-ER-CAL 33920-60E54 OBD Diagnostics, Inc. ALDL (GM OBD1) Cable with 12 pin SDL Connector to USB I get about 5 volts across M to A pins and about 12 volts across H to A pins MIL functions prop...	SwingDancer	1	1203	Aug 29, 2014 by TechSupport
	change display resolution for Rhinoview? (Preview) Is there config file or setting I can tweak to get a different sized window from Rhinoview? My Car PC's Monitor has a native resolution of 800 x 600. I cant seem to get a good view of Rhinoview. I have to move the window around to see the edges. thanks, randy H	randy h	11	1538	Aug 11, 2014 by TechSupport
	Swift in Trouble (Preview) Hi Rhinoman, Hi Forum! I'm new here today and very very excited what this Project is about, this is great stuff Rhinoman! So first about me: I'm from Germany and my car is a '92 Swift EA 1.0, at the moment barely 80.000km. Very few problems so far (New Battery, new tail exhause pipe) but now he's running in...	moonraker	0	929	Apr 26, 2014 by moonraker
	Cannot get RhinoView to connect. (Preview) Please help, I am using the RhinoPower USB OBD1 cable and trying to connect to my petrol Wagon R+ using an Msi Wind netbook running XP. Cable shows up in Device manager on comm11 so I have set that in RhinoView, tried both speeds to no effect. Any ideas please.	wagonR+	14	2043	Apr 2, 2014 by TechSupport
	2000 vitara 4u2 (Preview) Hi I have a 2000 vitara 4u2 with no spark or fuel ran perfect then all of a sudden this. now my dash lights have gone too but car will still turn over ???????? please can any one help.	sean952	2	859	Mar 3, 2014 by sean952
	2001 GV XL-7 (USA) (Preview) Hi all, I was wondering what all diags or software I would be able to do on my xl-7. Its a 2001 American version, also what cables would I need to iinterface... Thanks in advance, Roger	rcullens	1	951	Dec 17, 2013 by TechSupport
	Relationship between ECU part number and ECU Identification (Preview) What the Relationship between ECU part number and ECU Identification? in the picture below, the ECU part number is 33920-80GA0 , what is the ECU IDs of this module, is 33920-80GA ? please give me some advice. thanks,	quangtruong	1	1026	Dec 5, 2013 by TechSupport
	Using RhinoPower with Indian Suzukis. (Preview) Hello, Just received my cable, Thank you!. Tried hooking it up to an Indian SX4, though 2007 this ECU is certainly not OBD II complaint. the software keeps saying "bad data count" I suspect this relates to reading from the ECU. Here is a pic of the port, comparing this to the standard OB...	madmaxarjun	1	898	Dec 2, 2013 by TechSupport
	what in Rhinoview would confirm closed loop? (95 geo tracker) (Preview) Is there a particular sensor data set I can observe in Rhinoview that would confirm if my engine is running in Closed Loop? Its probably obvious but I cant figure out. thanks randy	randy h	2	944	Nov 22, 2013 by randy h
	ECU ID 1902, P/N #33920-65DA1 ( 1 2 ) (Preview) TPS - I seem to have three addresses #11, #12 & #38 - this is a 3 wire TPS by the way Throttle closed #11 is at 0, #12 is at 31, and #38 is at 16 - as the throttle is opened 11 & 12 increase gradually until at max throttle 11 is at 172 and 12 is at 204 - note that at max throttle the difference is also 31, this d...	fordem	88	24009	Jun 23, 2013 by TechSupport
	jimny engine light problem (Preview) hi there my name is tristan slight i live in western australia, australia i have a 2007 Suzuki jimny m13a vvt which i currently converted to a m18a engine everything went fine and ran well it has since done about 2000km. Today the engine light come on but still runs fine the only thing i have noticed is tha...	tslight	4	1710	Jun 1, 2013 by TechSupport
«First < 1 2 3 4 > Last» \| Page of 4 sorted by