RhinoPower Ltd

Members Login
Username 
 
Password 
    Remember Me  
RhinoPower EFI -> RhinoPower Forum -> RhinoView Diagnostic Software -> Connection Issues - JDM 1997 JB32W
Post Info TOPIC: Connection Issues - JDM 1997 JB32W
Ian


Member

Status: Offline
Posts: 5
Date:
RE: Connection Issues - JDM 1997 JB32W
Permalink  
 

It's a brand new battery reading 12V. I think you're right about an issue with a bad connection. Fortunately, my mechanic was able to do some work on the engine and the CEL went away but I will inspect ground points and wiring. Thanks for all your patience and assistance.



__________________
TechSupport


Guru

Status: Offline
Posts: 1354
Date:
Permalink  
 

That could be a bad connection somewhere, do you get the same reading if you put the meter directly across the battery?



__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Had to get my hands on a multimeter. Looks like I'm getting only 8V across the 2 bottom pins. Is this insufficient? Any ideas on what may cause this? Bad fuse/ground?



__________________
TechSupport


Guru

Status: Offline
Posts: 1354
Date:
Permalink  
 

That is correct, have you got 12V across the bottom two pins?

__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Pin 7 is not populated. 

 

Looks like only pin 5, 18 and maybe 12 are populated. Thanks!



Attachments
__________________
TechSupport


Guru

Status: Offline
Posts: 1354
Date:
Permalink  
 

Can you confirm that the diagnostic connector does not have pin 7 populated?

__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Thanks for the quick response. 

Switched to 15625 and restarted. No change at all.

If it helps, the sticker on the ECU says:

1 -4V MT

33920-81CA 1

112000-3781

12V



__________________
TechSupport


Guru

Status: Offline
Posts: 1354
Date:
Permalink  
 

Hello Ian
Please try changing the setting to 15625 and then restart the application.

__________________

1984 Suzuki SJ413K pick up, 1.6 16V Baleno engine
2000 Suzuki Vitara 1.6 8V, many mods
2004 Suzuki Ignis 1.5VVT 4Grip
2006 Suzuki Jimny 1.3VVT JLX+
and many more.
Ian


Member

Status: Offline
Posts: 5
Date:
Permalink  
 

Hi everyone,

I have a JDM 1997 JB32 Jimny Sierra with a G13BB engine and cannot connect to the tool. I have followed the instructions to install the required drivers and steps to connect the device to the computer. Baud rate is set to 7812. 

I am receiving RX error messages in the Bad Data count section. Can someone advise how to fix?

 



__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
RhinoPower EFI -> RhinoPower Forum -> RhinoView Diagnostic Software -> Connection Issues - JDM 1997 JB32W


Create your own FREE Forum
Report Abuse 		Powered by ActiveBoard